Search Results

Regulated emissions from four current production European vehicles were measured over the Common Artemis Driving Cycles (CADC). Particulate Mass and Particle Number measurements were made in accordance with the newly-developed draft Particulate Measurement Programme (PMP) developed for the UN-ECE's expert group on pollution and energy (GRPE). During the test programme measurements were also made of currently non-regulated emissions including PAHs and speciation of the particulate material and key hydrocarbons. CADC results are presented for each of the four vehicles tested (one conventional gasoline vehicle, two different types of diesel without Diesel Particulate Filter (DPF) and one diesel with DPF) with results measured on the regulated New European Driving Cycle (NEDC) test for comparison. The emissions results on the Artemis cycles showed some significant differences from those on the regulated (NEDC) test cycle.

Abstract An investigation into the pre-ashing of new gasoline particulate filters (GPFs) has demonstrated that the filtration efficiency of such filters can be improved by up to 30% (absolute efficiency improvement) when preconditioned using ash derived from a fuel-borne catalyst (FBC) additive. The additive is typically used in diesel applications to enable diesel particulate filter (DPF) regeneration and can be added directly into the fuel tank of the vehicle. This novel result was compared with ash derived from lube oil componentry, which has previously been shown to improve filtration efficiency in GPFs. The lube oil-derived ash utilized in this work improved the filtration efficiency of the GPF by −30%, comparable to the ash derived from the FBC additive.

The sweetpotato (Ipomoea batatas L. LAM.) is a versatile and underexploited food crop. Consumption of sweetpotato based processed foods provide β-carotene, which is the major precursor of vitamin A. The sweetpotato has the potential to provide antioxidants that may help reduce the radiation risks astronauts face while in space. Therefore the objective of this experiment was to evaluate β-carotene in dehydrated hydroponic sweetpotato cultivars. Hydroponic cultivars WHATLEY/LORETAN and NCC-58 were grown with and without 7-10 μmole of light. WHATLEY/LORETAN contained the highest amount of β-carotene content average of 31 μg/100g in dehydrated hydroponic sweetpotatoes compared to NCC-58 with 18.5 μg/100g.

Prior theoretical work relating barrier equivalent velocity (BEV) and change in vehicle velocity, ΔV, has either neglected restitution or mischaracterized its role. Based on fundamental structural dynamics principles, improved relationships between BEV, ΔV, coefficient of restitution, and vehicle mass and stiffness are formulated. These corrected relationships are then utilized in the assessment of four classes of vehicular impact testing: vehicle to vehicle (VTV), vehicle to infinitely massive rigid barrier (VRB), vehicle to infinitely massive compliant barrier (VCB) and vehicle to finite mass movable rigid barrier (VFMB).

The Swedish Biomimetics 3000's μMist® platform technology has been used to develop a radically new injection system. This prototype system, developed and characterized with support from Lotus, as part of Swedish Biomimetics 3000®'s V₂IO innovation accelerating model, delivers improved combustion efficiency through achieving exceptionally small droplets, at fuel rail pressures far less than conventional GDI systems and as low as PFI systems. The system gives the opportunity to prepare and deliver all of the fuel load for the engine while the intake valves are open and after the exhaust valves have closed, thereby offering the potential to use advanced charge scavenging techniques in PFI engines which have hitherto been restricted to direct-injection engines, and at a lower system cost than a GDI injection system.

This recommended practice prescribes clear and consistent labeling methodology for communicating important xEV high voltage safety information. Examples of such information include identifying key high voltage system component locations and high voltage disabling points. These recommendations are based on current industry best practices identified by the responder community. Although this recommended practice is written for xEVs with high voltage systems, these recommendations can be applied to any vehicle type.

This paper presents a numerical study on the impact of washcoat diffusion on the overall conversion performance of catalytic converters. A comprehensive transient 1D pore diffusion reaction model is embedded in state-of-the-art 1D and 3D catalytic converter models. The pore diffusion model is discussed with its model equations and the applied diffusive transport approaches are summarized. The diffusion reaction model is validated with the help of two available analytical solutions. The impact of basic washcoat characteristics such as pore diameters or thickness on overall conversion performance is investigated by selected 1D+1D calculations. This model is also used to highlight the impact of boundary layer transfer, pore diffusion and reaction on the overall converter conversion performance. The interaction of pore diffusion and flow non-uniformities is demonstrated by 3D+1D CFD simulations.

Abstract With the adoption of Vehicle-to-everything (V2X) technology, security and privacy of vehicles are paramount. To avoid tracking while preserving vehicle/driver’s privacy, modern vehicular public key infrastructure provision vehicles with multiple short-term pseudonym certificates. However, provisioning a large number of pseudonym certificates can lead to an enormous growth of Certificate Revocation Lists (CRLs) during its revocation process. One possible approach to avoid such CRL growth is by relying on activation code (AC)-based solutions. In such solutions, the vehicles are provisioned with batches of encrypted certificates, which are decrypted periodically via the ACs (broadcasted by the back-end system). When the system detects a revoked vehicle, it simply does not broadcast the respective vehicle’s AC. As a result, revoked vehicles do not receive their respective AC and are prevented from decrypting their certificates.

RADIOTRACERS were used to study the wear effects of engine speed, load, jacket water temperature, fuel temperature, and chromium-plated rings in a medium-speed diesel engine. One distillate fuel and two residual fuels were tested. This paper describes the tests and their results. Some of the conclusions are: The brake thermal efficiency with high viscosity residual fuel was essentially equal to distillate diesel fuel over a wide range of loads, providing the residual fuel was heated to the proper temperature. Engine speed did not affect the wear rate of cast-iron rings when distillate fuel was used, while with residual fuel wear decreased with increased speed. With distillate fuel, engine load had essentially no effect on cast-iron ring wear. With residual fuel, decreasing engine load produced a marked increase in ring wear*

COMPARISON of work capacity per unit mass and volume of different energy carriers shows that liquid hydrocarbons are superior to other energy sources. Solar and nuclear powerplants as well as their use in conjunction with a steam engine are examined in this paper. Suitability of an electric drive is discussed. Using a production 2-stroke diesel engine and its development forecast, a comparison is made of spark ignition, diesel, and gas turbine engines. The status of the free-piston engine turbine combination is reviewed.

RADIATION can produce almost instantaneous failure of modern aircraft lubricants, tests at Southwest Research Institute show. Two types of failures demonstrated are rapid viscosity rise and loss of heat conductivity. Furthermore, it was found that lubricants can become excessively corrosive under high-level radiation. Generally speaking, the better lubricants appeared to improve in performance while marginal ones deteriorated to a greater extent under radiation. When the better lubricants were subjected to static irradiation prior to the deposition test, there was a minor increase in deposition number as the total dose was increased.

This paper deals with the Coupled thermo mechanical analysis of a cylinder head, cylinder block and crank case with the liner of an uprated engine. The existing engine develops 780 hp output with mechanical driven supercharger and the engine is uprated to 1000 hp by replacing the supercharger with a turbocharger and new Fuel injection equipment. For uprating any engine, the piston and cylinder head are the most vulnerable members due to increased mechanical and thermal loadings. Mechanical loading is due to the gas pressure in the gas chamber and its magnitude can be judged in terms of peak pressure. Thermal loading is due to temperature and the heat transfer conditions in the piston surface, cylinder liner and the cylinder head. The relative importance of the various loads applied on the head and cylinder block in operation are assessed and a method of predicting their influence on the structural integrity of the components described.

mDSF is a novel cylinder deactivation technology developed at Tula Technology, which combines the torque control of Dynamic Skip Fire (DSF) with Miller cycle engines to optimize fuel efficiency at minimal cost. mDSF employs a valvetrain with variable valve lift plus deactivation and novel control algorithms founded on Tula’s proven DSF technology. This allows cylinders to dynamically alternate among 3 potential states: high-charge fire, low-charge fire, and skip (deactivation). The low-charge fire state is achieved through an aggressive Miller cycle with Early Intake Valve Closing (EIVC). The three operating states in mDSF can be used to simultaneously optimize engine efficiency and driveline vibrations. Acceleration performance is retained using the all-cylinder, high-charge firing mode.

The purpose of this ARP is to provide criteria that will lead to and support existing regulatory standards of systems for UAM/AMM/eVTOL aircraft such that the emergency systems will facilitate egress under emergency conditions. Consideration is given to existing requirements of the FAA and to the recommendations of aircraft operators and those involved in the manufacture or use of the emergency lighting system. Occupant safety is the primary objective, with appropriate provisions for crew (pilot) system control taken into consideration. Consideration is also given to autonomous aircraft in which passengers are required to egress without the aid or direction of crew. The criteria established herein are intended to produce an emergency lighting system that will comply with the Federal and International Regulations. However, these recommendations are but one means of meeting the objective.

eROSITA (extended ROentgen Survey with an Imaging Telescope Array) is a powerful X-ray telescope under development by the Max-Planck-Institut für extraterrestrische Physik (MPE) in Garching, Germany. eROSITA is the core instrument on the Russian SRG1 mission which is planned for launch in 2011. It comprises seven nested Wolter-I grazing incidence telescopes, each equipped with its own CCD camera. The mirror modules have to be maintained at 20°C while the cameras are operated at -80°C. Both, mirrors and CCDs have to be kept within tight limits. The CCD cooling system consists of passive thermal control components only: two radiators, variable conductance heat pipes (VCHP) and two special thermal storage units. The orbit scenario imposes severe challenges on the thermal control system and also on the attitude control system.

Worldwide, 1.2 million people die in road crashes yearly; 43,000 in Europe alone. This implies a cost to European society of approximately 160 billion euros, and takes up 10% of all healthcare resources. To reduce these rates, safety technologies have been developed which help to minimize the severity of injuries to vehicle occupants. However, studies have shown that most deaths due to road accidents occur in the time between the accident and the arrival of medical care. Therefore, a fast and efficient rescue operation would significantly increase the injured person's probability of survival. The aim of this project was to define the On-Board Unit (OBU) hardware and software installed in all modern vehicles which could request medical and technical support after a road accident. This device, based on the information from the vehicle sensors, automatically decides whether the car has suffered a road accident or not, the severity of the accident and the kind of accident (impact area).

THE NEW DIRECT-INJECTION diesel engines — the naturally aspirated 16000 and the turbocharged 21000 — were developed to power specific crawler and wheel vehicles built by Allis-Chalmers. Thus the original design and performance specifications were defined by the space available in these machines, and by the power and torque characteristics required by them. Also, the engines had to be suitable not only for commercial applications such as generator sets, shovels, and compressors, but also for oil field and marine service. Torque and speed requirements indicated that a 5¼-in. bore and 6½-in. stroke would give the desired performance. To meet the low heat rejection and good starting requirements, an open-chamber combustion system had to be used. The three-valve arrangement — two intake and one exhaust — was chosen because it offered low pumping losses and reasonable cost. This paper describes the design considerations and development work which produced the new diesel engines.*

The permanently increasing number of convenience and safety functions leads to higher complexity of in-car electronics and the rapidly growing amount of sensors, actuators and electronic control units places higher demands on high- speed data communication protocols. Safety-critical systems need deterministic protocols with fault-tolerant behavior. The need for on-board diagnosis calls for flexible use of bandwidth and an ever-increasing number of functions necessitates a flexible means of extending the system. None of the communication solutions available on the market until now (like CAN or TTP) have been able to fulfill all these demands. To solve these problems, BMW together with several semiconductor companies has developed a new protocol for safety-critical applications in automotive vehicles.

ALTHOUGH turbocharging of low-speed diesel engines has been used world-wide for a long time, it is only during recent years that it has been applied to high-speed diesels. This is the result of considerable engineering efforts from both the turbocharger and the diesel side that were put into the turbocharger, which appears to be a so utterly simple device. This paper de­scribes some of these engineering efforts. The basic design characteristics are developed with the point of view in mind that the turbo­charger has become much more than just an ad­ditional accessory. It is a vital component of the basic engine itself, contributing actively to the advancement of this prime mover. The basic de­sign characteristics center heavily around aero­dynamical and thermodynamical performance cri­teria which are so important in any advanced high-speed turbomachine.